Page 1 of 1
我沒事用啥nForce2呀~~~
Posted: Sun Mar 14, 2004 4:41 am
by AndCycle
喵阿弄上一個禮拜了 ...
問題還是一堆,
我已經可以寫nForce2上面上Gentoo的心得感想與新手指引了 =_=
--
這件事情告訴我們不要買新玩具來讓linux跑....
Posted: Sun Mar 14, 2004 5:41 am
by AndCycle
網路問題還未解決 ...
超過一定量的資料後會自動被斷線 =_=
Posted: Sun Mar 14, 2004 6:47 am
by AndCycle
AndCycle wrote:網路問題還未解決 ...
超過一定量的資料後會自動被斷線 =_=
noapic 顯然可以修好這個問題
http://kerneltrap.org/node/view/2410/7100
"WTF nVidia?! Have you noticed your APIC sucks?!"
Posted: Sun Mar 14, 2004 6:48 am
by AndCycle
AndCycle wrote:AndCycle wrote:網路問題還未解決 ...
超過一定量的資料後會自動被斷線 =_=
noapic 顯然可以修好這個問題
"WTF nVidia?! Have you noticed your APIC sucks?!"
我錯了 ... 剛剛一po完文就被斷了 ... 喵啦這啥鬼問題, 我今天睡醒就去買張螃蟹來頂 =_=#
Posted: Sun Mar 14, 2004 7:14 am
by AndCycle
nForce搞啥...
http://www.wlug.org.nz/NForce2Notes
"Network
The network controller on nForce2 based boards only works with a binary driver called nvnet that is supplied by nvidia in the package above. This seems to work fine and gives reasonable performance.
If you're using kernel 2.6, you will have to patch the NVidia source to make nvnet run.
See also ForcedEth, a reverse engineered open source ethernet driver for the onboard NVIDIA lan.
Note with regard to network performance
Sometimes you'll notice, when doing large transfers over your LAN, that your CPU usage goes through the roof and eth0 generates up to
500,000 interrupts a second. The nvnet driver is to blame; you can either load the module with 'optimizations=1' to optimize for CPU usage instead of throughput (interestingly, this doesn't seem to affect throughput at all), or you can load forcedeth, which makes it all go away. forcedeth should be included in 2.4.24+ and is within 2.6.3+."
Re: 我沒事用啥nForce2呀~~~
Posted: Tue Mar 16, 2004 10:44 am
by feuer
AndCycle wrote:這件事情告訴我們不要買新玩具來讓linux跑....
我買了一塊有 DVI 的便宜的 Redaon 9200 顯示卡，
果然也是一堆狀況，幸好，vesa mode 勉強可跑。
Posted: Thu Mar 18, 2004 8:31 pm
by AndCycle
網路問題還是沒解決 ...
插張螃蟹也是一樣 ...
持續性的網路連線後會有突然中斷數十秒的狀況,
SSH 連上去放著 top 跑一陣子後就會 network error
Posted: Thu Mar 18, 2004 10:07 pm
by paar
加油,
不知道從什麼時候開始,
我買硬體前都會先做功課......到底它能不能在 linux 用?
Posted: Sun Mar 21, 2004 4:51 pm
by AndCycle
結論出來了 ... 問題不是 nForce 製造的 (死)
賠了一顆CPU的差價換個更爛的硬體得到了答案 ...
作怪的是 iptable ~_~
Posted: Mon Mar 22, 2004 10:55 pm
by paar
O~ My God!!
Posted: Wed Mar 24, 2004 8:55 am
by visa
有這麼難æ
Posted: Thu Mar 25, 2004 5:56 pm
by AndCycle
visa wrote:有這麼難搞嗎 我也想用 NFORCE 來裝說~~~
現在的 kernel 不會難搞, 基本上主要的功能都沒問題了, 都是些不影響正常使用的小毛病就是了